Names | |
---|---|
Other names
Tetraazidosilane
| |
Identifiers | |
3D model (
JSmol)
|
|
ChemSpider | |
PubChem
CID
|
|
CompTox Dashboard (
EPA)
|
|
| |
| |
Properties | |
Si(N3)4 | |
Molar mass | 196.1659 g/mol |
Appearance | White crystals |
Melting point | 212 °C (414 °F; 485 K) |
Reacts | |
Except where otherwise noted, data are given for materials in their
standard state (at 25 °C [77 °F], 100 kPa).
|
Silicon tetraazide is a thermally unstable binary compound of silicon and nitrogen with a nitrogen content of 85.7% (by molar mass). This high-energy compound combusts spontaneously and can only be studied in a solution. [1] [2] [3] A further coordination to a six-fold coordinated structure such as a hexaazidosilicate ion [Si(N3)62− [4] or as an adduct with bicationic ligands Si(N3)4·L2 [2] will result in relatively stable, crystalline solids that can be handled at room temperature.
Silicon tetraazide is synthesized by conversion of silicon tetrachloride with sodium azide in benzene. [1] [3]
The reaction of silicon tetrachloride with an excess of sodium azide at room temperature in acetonitrile will result in the formation of sodium hexaazidosilicate (Na2[Si(N3)6) which by adding ligands such as 2,2′-bipyridine and 1,10-phenanthroline will result in stable silicon tetraazide adducts. [2] Other bases such as pyridine and tetramethylethylenediamine will not react with the hexaazidosilicate ion. [2]
Another preparation of a bis(triphenylphosphine)iminium hexaazidosilicate salt [(Ph3P)2N]2[Si(N3)6 is possible by conversion of bis(triphenylphosphine)iminium azide [(Ph3P)2N]N3 with silicon tetrachloride in acetonitrile, where Ph is phenyl. [4]
Silicon tetraazide is a white crystalline compound that will detonate at even 0 °C. [1] The pure compound, and also silicon chloride triazide SiCl(N3)3 and silicon dichloride diazide SiCl2(N3)2 contaminated samples, can detonate spontaneously without clear cause. [5] The compound is susceptible to hydrolysis. [3] It is soluble in diethylether and benzene. [1]
The addition compound with 2,2′-bipyridine is much more stable. A melting point of 212 °C with a melting enthalpy of 110 J/g is recorded. The DSC measurement shows at 265 °C a sharp exothermic reaction with an enthalpy of −2400 J/g. Similar results are found for the addition compound with 1,10-phenanthroline. As the hemiacetonitrile solvatated isolated compound expels solvent at 100 °C, and shows then in the DSC measurement from 240 °C onwards a strong exothermic reaction with a generated heat of 2300 J/g. [2] The enthalpies are higher than that of sodium azide with −800 J/g, [6] but still lower than the values encountered with classic explosives such as RDX with −4500 J/g. [2] The addition compounds are stable in solution. It can be concluded from IR-spectroscopy and proton NMR data that no dissociation occurs in silicon tetraazide and 2,2'-bipyridine or for example 1,10-phenanthroline. [2] The bis(triphenylphosphino)iminium hexaazidosilicate salt [(Ph3P)2N]2[Si(N3)6 on the other hand is relatively stable. The compound melts at 214 °C and shows in the DSC measurement at 250 °C a reaction. [4] One mass spectrometry coupled thermogravimetric analysis investigation indicated as reaction products nitrogen, silicon tetraazide and hydrazoic acid. [4]
A practical application of free silicon tetraazide is unlikely due to the high instability. In solution the compound has potential uses as raw material for nitrogen-rich materials. [2] One application as reagent in the manufacture of polyolefins has been patented. [7] The stabilized adducts can serve as energetic compounds as a replacement for lead azide. [2]